Troubleshooting & Service for GL/GS Systems 50 Hz. 2 Balboa’s Patented M7 Technology. Balboa BALBOA INSTRUMENTS, INC. Kia ceed service manual. 900854 Page 1 PC Spa Dashboard Control User Guide balboa-instruments.com EL/GL Series - Mach 3. Output Features Quadrant J23 + W1 – 2-Speed Pump 1 4-A – OR 1-Speed Pump 1 with DIP Switch A5 J50 + W4 – Audio Visual - always hot, no relay 6-A J17/26 + W7 – 1-Speed Blower (W3 to J46) 6-B – OR Single-Speed Pump 2 or Pump 3 (W3 to J62) J47 + W2 – Circ Pump 8-A J29 + W2 – Ozone (Same voltage as Circ Pump, if used) 9-A – Note X-03 option board for retro fit J20 – Spa Light (12V only) 9-A System can be factory configured for either a Duplex Topside Panel, a Serial Standard Panel, or a Serial Deluxe Panel. Note: Some panels styles are not available depending on system configuration. Consult your Balboa product representative for details. 120V Conversion Option - Add jumper from Red AC (J32) to White AC (J11) and set DIP switch A10 to ON. X-P Used for a 1-speed Pump output. ![]() ![]() X-P231 Can replace the X-P in cases where branch circuit protection is needed for high amperage devices that would over-burden power input fuse F5 (1-A) on the main PCBA. • J6 on the X-P231 connects directly to Black AC by using J66 or J65 on the main board (1-B). • Connect J7 wire on the X-P231 to J60 on the main board (7-E). • Connect W1 on the X-P231 to Red AC on the main board (2-D). X-2SP Kit Adapter PN 25339 is used in conjuction with an X-O3 to run a 2-speed pump 2. No Blower is available when this kit is used. • J4 connects to Black AC (3-A) using J61 or J62 on main board. Gb Instruments User Guide• Connect 2-speed pump to J7 on X-03. PN 53913 G C G C J6 J7 J4 J5 J2 W12 K1 VS500Z Configuration Guide VS500Z Expander Board Options Instruments Balboa Incorporated VS-P2 Adapter Wire PN 25339 To J5 on X-O3 To J17/26 (Blower/P2) PN 53544 PN 53681 X-P332 Used for an additional 2-speed Pump output. • J6 on the X-P332 connects directly to Black AC by using J66 or J65 on the main board (1-B). User Guide Definition• Connect J7 wire on the X-P332 to J13 on the main board (9-E). • Connect W1 on the X-P332 to Red AC on the main board (2-D). PN 55137 X-Mount P Used for mounting any Expander Board in a plastic enclosure. Standoffs attach to heater mounting bracket. PN 53933 Document PN 40540_M 1-30-2007 A B C D E A B C D E 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 NOTE Regarding J12 (Quadrant 9-D): When J12 on the Main Board is jumpered on pins 2 & 3, the system is in VS50xZ compatibility mode. If J12 on the Main Board is jumpered on pins 1 & 2, the system is in VS51xZ/VS5xxSZ/VS5xxDZ compatibility mode. G C J6 J4 J2 W12 K1 G C J6 J3 J2 W12 K1 F10A 250V F5 X-B Used for a Blower output ONLY.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |